4841 Starter Motor Tejo Tumuluri

Starter motor

The main purpose of the starter mote is to start the engine. There are three types of starter motor, Inertia, Pre-engaged and gear reduction.

Before we took apart the starter motor we had to carry out a bench test and the readings we got was 11.9 volts and 33.8 amps to meet the specs we had to get no less than 11 volts and between 30 to 50 amps and we were within the specs.

Armature.

After taking apart the starter motor we had to do a visual check on the armature to see if there was any overheating, burning, physical damage and poling, the armature had no damage in anyway.

Then we did a ground test to see if the armature was grounded to meet the specs we had to get a reading of infinity and that’s what we got. So we moved on to the continuity test.

Then we moved on to check the diameter of the armature to find out if there was any wearing. Results we got was 30mm so we were within the specs and we also checked the mica undercut for any physical damage, we got 0.8mm to meet the specs we had be within 0.7mm-1.00mm so we met the specs.

Armature short test

We carried a short test using a growler to see if the armature was shorted, to carry the test you need a hacksaw blade, growler and the armature. Place the armature on the growler and the growler on then place the hack saw blade on top of the armature and rotate the armature to see if the blade vibrates, if the blade vibrates the armature is shorted and ours wasn’t shorted.

Brushes

We had to measure the brushes to see if there were worn, if there were they wouldn’t make contact with the armature when the armature rotates. We had three brushes and the readings we got was 5mm which met the specs.

Solenoid magnetic switch

We did the pull winding test by connecting the switch to the 9v power supply to see if the plunger will pull in and ours did so the magnetic switch is in working order.

Hold in winding test

We did the hold in winding test by connect the 9 volt power supply to the solenoid body and the plunger should remain in and when the power is disconnected the plunger should automatically release and our did so it is working order.

Then we put the Starter Motor back together and did the bench test to see if we put back together alright and also to check if it working after re-assembling and the results we got was 12.26 volts to meet the specs it should be no less than 11 volts and for current we got 45.1, to meet specs it should be between 30 to 50 amps so we meet the specs for volts and current and the alternator is fine and in working order.

                

4841 Relays Tejo Tumuluri

Relays

Relay is used to switch between circuits. Relay uses low amperage to switch a higher amperage circuit. Inside the relay there is a coil it creates magnetism, the circuit have a set of contact points that switched by the magnetism.

The test we had to do was on a 5 pin relay and the pins designations was,

·      86 positive side of a control circuit.

·      85negative side of control circuit.

·      30 battery supply for switched circuit.

·      87a normally closed switch circuit.

·      87 other switch circuit.

Then we had to wire up a relay on the circuit board with 2 light bulbs that are controlled by a switch. Then we had to take the reading of available voltage when the circuit was on and also when off.

 Circuit off                               Circuit on

86) 13.07v                             86) 13.12v

85) 13.06v                             85) 0.00v

30) 13.13v                             30) 13v

87a) 13.15v                          87a) 0.00v

87)  0.00v                              87) 13.08v

There was voltage change on each terminal because:

·      86 Is the input position so there will always be 13 volts there.

   85 There is 12 volts at off position when goes on there is 0.00 volts because it is consumed.

·      30 Is the input so there will always be 13 volts at that point.

·      87a There is 13 volts because the circuit is off and the coil is not magnetised so there is no switching.

·      87 is 0 volts because the circuit was on and the coil is magnetised and switched from 87 to 87a.

4841 Battery Tejo Tumuluri

Battery Assessment

The main purpose of the battery is to power the starter motor and the ignition system and also provide power to accessories in the car. Car battery comes in 12 volts, and has six plates which are 3 positive plates and 3 negative plates and each plate has 2.1 volts = 12.6 volts. Batteries come in 3 types’ conventional, maintenance free and gel type.


Car we carried the test was on:

Vehicle: Mazda

Model:323
year: 1981
Make of Battery: Lucas
Battery No: 127HD
CCA: 400

On 3/05/11 we carried out a battery testing assessment we started off with a visual check to see if anything requires attention and we found out that the negative terminal needs cleaning and we can clean by using soda/water and apply petroleum gel to protect it from rust. Then we did a test on electrolyte to find if the levels were high, ok or low. And the results we got were okay. So we moved on to perform an open circuit voltage test the result we got was 13.4 volts, state of charge percentage was over 100%. Further action we had to take to continue the test was to remove the surface charge.

Specific Gravity Test

cell	1	2	3	4	5	6
Reading	1.275	1.275	1.275	1.275	1.275	1.275
Colour	Green	Green	Green	Green	Green	Green

The above readings were from the gravity test and the allowable specs have to be within 25-50 and the variation we got was 0 so we passed the gravity test.

High Rate Discharge Test

We had to carry out a load test on the battery on using a load tester we had to determine the load current and apply which was 200 (to get the load current you divide the cca rating by 2, 400/2 =200). You apply the load for 10 seconds and battery must hold above 10 volts and our result was 10.4 so we met the specs.

Last test was analysing our results and note findings and recommendations.

1.  Visual check. We did a visual check on the battery and we found out that the negative terminal has corrosion on it. To clean it you will need to use soda water.

2.  Specific Gravity: for the specific gravity test all the results we got was same and equal which states that all the cells have equal electrolyte readings.

3.  For the ocv test the results we got was more than the specified voltage. We got a reading which was 13.4 volts which has surface charge we removed by cranking the engine.